The Ray5 Mini supports connection to Longer LaserBurn software on both mobile devices and PCs. You can connect through Wi-Fi on mobile or use a serial port or IP address on a PC.

This guide walks you through the connection process, design settings, file management, and engraving workflow. Follow the steps below to get your RAY5 Mini ready for engraving.

1. Connect via Wi-Fi in AP Mode

In AP mode, your phone connects directly to the Ray5 Mini's Wi-Fi, but will lose internet access. For full internet access, use STA mode.

  1. Open the LaserBurn app and go to the Home screen.
  2. Tap the not connected icon.
  3. When prompted with “Allow LaserBurn to access this device?”, select ALLOW ONLY WHILE IN USE to allow the app to search for Wi-Fi.
  • Open your phone’s Wi-Fi settings, find the network named LongerLaser_XXXX, and connect with the password 12345678.
  • Then, enter 192.168.0.1 in the app, click Connect, and wait for the “connection succeeded” message.

2. Connect via Wi-Fi in STA Mode (Recommended)

Open your phone's Wi-Fi settings. In the LaserBurn app, tap the disconnected icon to enter the network configuration screen. Tap Add in the top right corner.

Tap Scan device, select the LongerLaser_XXXX network, and connect using the password 12345678.

After connecting, return to the app and select Set STA mode to link the Ray5 Mini to your home router (2.4G only).

Enter the router’s password. The indicator light will turn orange (breathing) during connection and green once successful. If it stays orange, restart the process.

  • Return to LaserBurn, tap Connect network at the bottom, and ensure your phone is connected to the same Wi-Fi used in STA mode.
  • Once it reaches 100%, tap FINISH to return to the device list.

Note: Once connected, tapping anywhere in the device list will disconnect. Tapping again will reconnect.

3.Design & Parameter Settings

Import graphics via drawing tools, text, QR codes, camera, photo albums, or the material library. In Layer settings, configure:
  • Mode: Line or Fill
  • Laser Type: 2.5W / 3.5W 450nm Blue light
  • Processing: Engrave or Cut
  • Material: Select from material library to auto-apply settings; customize manually if needed

You can adjust up to 11 parameters and use color-coded layers to assign different settings to different elements.

4. File Management

After connecting, preview uploaded files. To delete a file, swipe it left in the list. If storage is full, delete unnecessary files before uploading new ones.

5. Start a Project

Run the LaserBurn app and connect it to the RAY5 mini. Add a graphic, click Edit to set the size and position, then click Layer to adjust the graphic parameters. After setting, click next in the upper right corner.

There are 4 values for accuracy: Ultra Fine, Fine, Fast, and Ultra Fast. The default value is Fine. For more precision, select Ultra Fine. For more efficiency, select Fast or Ultra Fast.

Click Border setting to set the speed and patrol power. After setting, click frame to patrol the border. After confirming that the engraving position is correct, click Start to start engraving.

Once you’ve confirmed the focus is properly adjusted and goggles are worn, click Confirm to confirm the file name. The file will then upload to the Ray5 mini. After the upload is complete, click Confirm to start the engraving task.

The app will display the task progress. You can click Pause to pause the task or click Stop to cancel it. When the task is completed, a 'Work completed' prompt will appear. Click Confirm to return to the Home page.

Part 2: PC Connection Guide (LaserBurn Desktop Software)

1. Connect the Ray5 Mini

Open LaserBurn, go to the Device window, and click Connect. Select the Ray5 Mini model and click Confirm.

Two connection options are available:

  • Serial Port: Choose the correct COM port and click Connect. If it fails, check the port status or conflicts.
  • IP Address: View the IP address via Serial Port connection first, then use it to connect via network.

2. Control Panel Overview

  • Displays basic machine information

  • Set the machine's origin (zero point)

  • Reset the machine
  • Set step movement distance (Distance)
  • Enter X/Y coordinates and click To to move
  • Use Manage to save frequently used positions and move to them quickly

3. Drawing & Parameter Setup

  • Use the left toolbar to draw shapes or import designs
  • Double-click the right layer panel to set laser parameters such as power, speed, and accuracy

4. Engraving Workflow

  • In the Device tab, click Engraving to enter engraving mode

Set key parameters:

  • Laser Feed Speed: Border tracing speed
  • Laser Feed Power: Border tracing power

Click Border to preview the engraving position. Once everything is set, click Start Engraving

5. During the Engraving Process

Adjust in real-time using:

  • Feed rate multiplier for speed
  • Laser power magnification for power

Tap Pause to pause or Stop to cancel the task.

Conclusion

Connecting the Ray5 Mini to LaserBurn is simple once you understand the available connection methods.

On mobile, you can use AP mode or STA mode to connect the machine through Wi-Fi. On PC, you can connect through a serial port or IP address.

After connecting, LaserBurn lets you prepare designs, adjust parameters, manage files, and start engraving. Follow the steps above to set up your Ray5 Mini and begin your next engraving project.

0 commentairesur LONGER How To｜Guide to Connecting Ray5 Mini with LaserBurn (Mobile & PC)

Dernières histoires

Cette section ne contient actuellement aucun contenu. Ajoutez-en en utilisant la barre latérale.