LONGER ePrint Embroidery Effect AB Transfer Film Quick Start Guide V1.0

Welcome to the Longer ePrint Embroidery Effect AB Transfer Film Transfer Process.

Embroidery Effect is a transfer technique that uses specially designed printing patterns and layered textures to create a visual appearance similar to embroidery. With the AB Transfer Film process, the printed design can be transferred onto fabric while maintaining clear details and textured effects.

This guide covers the complete Embroidery Effect AB Transfer Film workflow, including material preparation, printing, AB Film lamination, heat transfer, and final inspection. Please read it carefully before operation to understand the material characteristics, key steps, and precautions to avoid common issues and reduce material waste.

Tips: Always operate in a dry and dust-free environment. Dust and moisture may affect transfer quality. Unused AB Transfer Film should be sealed and stored away from direct sunlight.

1. Material Preparation and Printing

(1) Before printing, prepare the AB Transfer Film correctly.

The A Film is a transparent base film used as the printing carrier, while the B Film is a blue roll film used as the protective and transfer support layer. For printing, place the A Film at a 45° angle and remove the transparent protective paper. The adhesive side should face upward as the printing surface.

(2) After confirming the printing file, upload it to the software and check the image preview, position, and expected effect.

(3) Recommended printing settings:

• Quality: High
• Speed: High

Select the "Embroidery Effect" printing mode and adjust the required Texture Layers according to the desired texture depth.

(4) For batch printing, make sure the printing position is correct and there is no collision during operation. After printing, check that the surface is clean, free of dust or foreign particles, and that the design details are clear.

2. AB Film Lamination Process

(1) Before lamination, check the B Film to ensure the surface is smooth, flat, and free from defects.

(2) Prepare the LONGER Laminating Machine and feed the B Film from the bottom through the machine rollers. Complete the AB Film lamination process according to the recommended machine parameters.

(3) After lamination, inspect the semi-finished material. The laminated surface should remain flat, with no bubbles or bonding issues.

3. Heat Transfer Process

(1) First, preheat the fabric using a Heat Press Machine.

(2) After cutting, separate the AB Film. The design is transferred onto the flexible B Film, while the A Film should be retained for later use.

(3) Use the remaining heat from the fabric to warm the B Film, then firmly press the B Film onto the fabric with a supporting cloth layer.

(4) Next, manually peel away the B Film and remove any adhesive residue from blank areas. Check that no design remains on the B Film.

(5) Use the A Film retained from the previous step and attach the non-release side to the design surface. After heat pressing, remove the A Film and clean any remaining adhesive residue.

4. Final Product Inspection

After completing the transfer process, carefully check the finished product. A qualified transfer result should have:

• Strong adhesion without peeling
• Clear Embroidery Effect texture
• Smooth surface without defects

Embroidery Effect AB Transfer Film Troubleshooting Guide

During the Embroidery Effect AB Transfer Film process, issues may occur due to material handling, environmental conditions, or incorrect parameter settings. The following guide helps identify common problems and provides possible solutions.

1. Printing Issues

Blurry Embroidery Texture or Ghosting Effect

Possible causes:

• A Film is not properly fixed during printing
• Print head is clogged

Solutions: Secure the film properly before printing and perform print head calibration and cleaning to ensure stable ink output.

Gray Colors, Poor Opacity, or Thin 3D Texture Effect

Possible causes:

• Texture Layers setting is too low
• Ink has separated due to insufficient mixing

Solutions: Increase the Embroidery Effect Texture Layers during printing. Stir the ink thoroughly before operation to ensure consistent color and texture performance.

2. AB Film Lamination Issues

Large Bubbles Between Films or Poor Adhesion in Some Areas

Possible causes:

• Dust contamination during operation
• Insufficient pressure from the laminating rollers

Solutions: Operate in a dry and dust-free environment. Adjust the Laminating Machine roller pressure and maintain a steady lamination speed to remove trapped air.

Design Peels Off with A Film or Texture Becomes Incomplete

Possible causes:

• A Film is peeled too vertically or too quickly
• Adhesive layers have not fully bonded

Solutions: Peel the A Film slowly at a 45° angle. After lamination, wait approximately 3 minutes before cutting to allow the adhesive layer to stabilize.

3. Heat Transfer Issues

Embroidery Design Peels Off or Becomes Incomplete

Possible causes:

• Fabric surface contains oil, dust, or fibers
• Heat press temperature or pressing time is insufficient

Solutions: Pre-clean and pre-press the fabric before transfer. Increase the Heat Press Machine temperature or extend the pressing time according to the material requirements.

Design Shifts or Texture Becomes Distorted

Possible cause: Fabric was not properly positioned during transfer.

Solution: Secure the fabric with high-temperature masking tape before heat pressing.

Surface Bubbles, Layer Separation, or Hollow Areas Inside the Texture

Possible causes:

• Moisture remains in the fabric
• Fabric was not fully dried before transfer
• Air was not completely removed during pressing

Solutions: Dry the fabric completely before transfer. During heat pressing, apply sufficient pressure to ensure proper bonding and remove trapped air.

Adhesive Residue Remains on Fabric Surface

Possible cause: Heat press temperature is too low.

Solutions: Increase the heat press temperature. Remaining adhesive residue can be gently removed with anhydrous alcohol.

4. Finished Product Usage Issues

Image Becomes Hazy After Washing or Embroidery Texture Peels Off

Possible causes:

• Production environment has excessive moisture
• Adhesive layers were not fully bonded

Solutions: Maintain a dry and dust-free production environment throughout the process. Recheck and optimize transfer parameters if necessary.

Design Edges Lift or Texture Layers Separate

Possible causes:

• Edges were not pressed firmly enough
• Stretch fabrics have weaker adhesion

Solutions: Pay special attention to pressing the edges of the design. For stretch fabrics, apply appropriate adhesion enhancement treatment before transfer.

Design Turns Yellow or Embroidery Texture Fades

Possible causes:

• Long-term exposure to strong sunlight
• Storage under high temperatures
• Improper curing or heat control

Solutions: Store finished products away from direct sunlight at room temperature. Strictly control curing conditions and avoid exceeding recommended heat press temperature limits.

Conclusion

By following this guide, you can complete the entire Longer ePrint Embroidery Effect AB Transfer Film process. During operation, please carefully follow each step and pay attention to the material condition, environmental requirements, and parameter settings to achieve stable transfer results.

If you encounter any problems during use, please feel free to contact us. We will help you quickly identify and solve the issues to ensure a smooth transfer process.